Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Blog Article

Don't ignore the forklift at the workplace. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight blocked the motorist's view, and the individual in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising heavy products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the load is secure and reputable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork should not be elevated expensive, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a specific security range from the automobile ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when stacking or packing. .
8. The elevation of the load should not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a prompt way, and they will never ever operate with diseases or hide them.

packing and unloading.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to work with a solitary fork or utilize a fork top or draw. In unique circumstances, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle need to be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to use forks to lift workers to take part in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or dispirit the parking brake button.
3. The engine is turned off and the power is removed. (Except for unique conditions, such as the driver does not leave the vehicle's line of sight and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak must likewise be checked and the seals must be changed in time.

Forklift Safety Operation Specifications.
1. You should inspect before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming ought to not be also sharp to avoid the tendency of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they encounter big or hefty goods and most likely to the chauffeur's view, they should take the turning around exercise
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not Stand-on Electric Pallet Stacker allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is raised.
8. Do not drive side to side Electric Forklift Truck for Warehouse on slopes
.
Auto parking is not permitted under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the exact same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844